Spigen Tempered Glass Screen Protector [GlasTR EZ FIT] designed for iPhone 14 Pro [Case Friendly] – Sensor Protection / 2 Pack

Best Protectors – Easy to Appy
Life saver! This glass screen protector is like an invisible shield for my phone. I can’t count how many times it’s saved me from a cracked screen.It’s so clear, I forget it’s even there until it saves my phone from a nasty fall. Easy to apply, no bubbles, and it doesn’t interfere with touch sensitivity. Plus, it’s fingerprint resistant, so my screen always looks sleek. It’s like insurance for my phone’s most vulnerable part. If you love your phone, do it a favor and get this screen protector.Five stars for durability and peace of mind!

Perfect fit and super easy setup, see my tips
I really like these Spigen screen protectors, mainly because the included alignment frame makes installing them super easy.If you are getting a new iPhone 14 the best thing to do is to have these screen protectors ready to go before you even open your new phone. The phone comes with a sticky paper protector on the screen already, and simply removing the paper protector and immediately installing one of these Spine protectors saves you from having to clean the screen off. If you’ve already opened your phone that’s no problem, you’ll just want to use the included wet wipes to get the screen completely clean before installing the new protector.I recommend you go into a small room where you can close the door and eliminate most airflow. Turn your home’s heating or cooling fan off for a few minutes while you do the install so you don’t have dust flying around. A bathroom works great for this, and if you want you can even run the shower on hot for a few minutes first. This will build up steam in the air which will cause any floating dust to fall to the ground.If you’re working in the bathroom the closed toilet lid makes a great little workspace for this project.Before you start I recommend holding the screen protector frame up to your phone so you can see how it’s going to fit over the top. Make sure you have the “TOP” marker on the frame on the top of the phone where the speaker and camera lenses are. Also notice that there’s a little tab on the inside of the screen protector frame that you’ll pull to remove the film from the back of the screen protector and reveal the sticky side of the glass. Once you’re familiar with the design set the frame aside for now.To install the protector first make sure your screen is super clean. If you’ve already removed the factory screen protector just wipe down the screen with the included wipes and make sure there aren’t any smudges or signs of dust as you tilt the screen at various angles. If you have a can of compressed air you can use it as a final step to blow off any dust, but it’s not a requirement as long as you get things really clean with the wipes.As soon as you feel like you’ve got the screen as clean as it can be sit the phone down on a flat surface (again, the closed toilet lid is perfect for this), and immediately peel the back film off the protector and sit the protector over the phone (make sure you have the “TOP” on the top of the phone as before). Press down everywhere on the frame and then run your finger back and forth on the center strip a few times. Keep pressing around on it for about 30 seconds.Next carefully peel off the center strip from the frame, while continuing to apply pressure everywhere else so you don’t accidentally pull up the screen protector itself while pulling off the tape. Once all the tape is removed from the center section the alignment frame will lift off the phone.Now you’ll be left with the screen protector on the phone with one more protective film on top. Leave the film on for now and use the included rubber squeegee to go over the whole screen with swiping motions to force out any bubbles that might be lurking under the film. Once you’ve gone over it a few times peel off the final film.That’s it, your protector should be securely installed in the perfect alignment without any bubbles underneath. You can use the included screen cloth to give it one final wipe to remove any smudges or fingerprints.If for some reason you find that there’s some annoying dust stuck under the protector you can repeat the process using the second included protector. Hopefully when you pry up the first protector it will do a great job of pulling up any dust from the screen and you can immediately install the second protector without needing to touch the screen at all.

As capas e películas desta marca, são muito confiáveis, por ultimo usei uma capa para meu iphone 14 pro, original da apple, o telefone quebrou a traseira toda. Quando usei a capa da spigen em meu modelo anterior, nunca tive problema, com inumeras quedas, o telefone sempre esteve protegido

Harika harika harika

The screen is easy to out in. Just make sure it’s the right way up. Text in mine was upside down when facing the right way.